quality control raises a handful of sensible questions. This page answers them in order, starting with the fundamentals and moving to applications.
This page was last updated on 2026-02-12 and is reviewed periodically as new material appears.
Practical HPLC testing depends on careful sample preparation and instrument maintenance. Samples may require filtration, dilution, pH adjustment, or extraction to avoid column damage and matrix interference. Mobile phases are degassed and filtered, and columns are equilibrated before injection. Common problems include peak tailing, baseline drift, ghost peaks, carryover, and co-elution of analytes. Documentation of instrument logs, calibration records, and electronic audit trails supports data integrity and traceability. Ongoing training and routine maintenance help reduce variability between analysts and laboratories.
Quality control laboratories use HPLC to check identity, purity, concentration, and stability of raw materials and finished products. A validated method specifies the column, mobile phase, flow rate, detection wavelength, injection volume, and run time. Samples are prepared and compared against reference standards of known concentration. The resulting chromatogram provides quantitative data, such as assay values and impurity levels. This approach is common in pharmaceutical, food, environmental, and industrial testing where consistent measurements are required.
Validation establishes that a method is suitable for its intended purpose. Typical parameters include accuracy, precision, specificity, linearity, range, limit of detection, limit of quantification, robustness, and stability of standards and samples. Acceptance criteria are defined in advance, and results are documented in a validation report. Regulatory guidance for pharmaceuticals, foods, and environmental testing differs, so the applicable framework must be identified. Ongoing verification uses control samples and trend charts after validation. Method transfer to another laboratory may require partial revalidation.
Routine quality control includes blanks, duplicates, spiked samples, and certified reference materials. Calibration curves are prepared with standards at several concentrations, and the detector response is checked for linearity. Carryover, column aging, mobile phase evaporation, and temperature drift can shift retention times or peak areas. Maintenance such as replacing seals, filters, and columns helps prevent failures. Records of injections, integration, and deviations support traceability. Audits may request raw data and instrument logs for each batch.
| Parameter | Typical acceptance criterion | Notes |
|---|---|---|
| Resolution | ≥ 1.5 | Baseline separation of adjacent peaks |
| Tailing factor | ≤ 2.0 | Peak symmetry measure |
| Theoretical plates | > 2000 | Column efficiency indicator |
| Injection repeatability | ≤ 2% RSD | Relative standard deviation for replicate injections |
| Linearity | r² ≥ 0.995 | Calibration curve over the working range |
Detection in HPLC testing commonly relies on ultraviolet-visible absorbance, fluorescence, refractive index, or mass spectrometry. A diode array detector records full spectra across a wavelength range, which helps identify co-eluting peaks. Mass spectrometry provides mass-to-charge ratios and can confirm molecular identity at low concentrations. The choice of detector depends on analyte structure, required sensitivity, and whether quantitation or identification is the goal. No single detector works for every compound, and method development often compares responses before selecting one.
High-performance liquid chromatography is an analytical technique that separates components of a liquid sample by passing it through a packed column under pressure. A pump delivers a mobile phase at a controlled flow rate, and an injector introduces the sample into the stream. Differences in interaction with the stationary phase cause analytes to migrate at different rates. Detectors record elution as peaks, and a data system converts signals into a chromatogram. The method is suited to compounds that dissolve in a liquid and are not volatile enough for gas chromatography.
Instrumentation includes a solvent delivery system, an autosampler, a column oven, and one or more detectors. Reversed-phase columns with chemically modified silica are widely used, but normal-phase, ion-exchange, size-exclusion, and affinity modes exist for specific separations. Detectors may rely on ultraviolet absorbance, fluorescence, refractive index, or mass spectrometry. Column temperature, mobile phase composition, and flow rate are adjusted to improve resolution. System pressure is monitored because rising pressure can indicate column blockage or deteriorating packing.
Separation performance depends on particle size, pore size, column length, and the chemistry of the stationary phase. Smaller particles generally improve efficiency but require higher pressure and suitable instrumentation. The mobile phase often contains buffers and organic solvents that influence retention and selectivity. Testing labs select conditions based on the analytes, sample matrix, and required sensitivity. Method development frequently involves screening several columns and solvent mixtures before a final set of conditions is chosen.
Method validation establishes that an HPLC procedure is suitable for its intended use. Key parameters include accuracy, precision, specificity, linearity, range, limit of detection, limit of quantitation, and robustness. Accuracy measures agreement with a true or accepted value, while precision describes repeatability and intermediate precision. Specificity confirms that the method measures the analyte without interference from impurities, degradants, or excipients. Validation is documented in a protocol and report, and acceptance criteria are set before experiments begin. Regulatory guidance varies by region, but the general principles are widely harmonized.
System suitability testing is performed before and during analytical runs to confirm that the instrument and method are working as expected. Common checks include retention time, peak area, resolution between critical pairs, tailing factor, and theoretical plate count. Results are compared with predefined limits, and a failed check requires investigation before sample results are reported. Quality control samples at low, middle, and high concentrations are injected at intervals to monitor accuracy and precision. Blank injections detect carryover and contamination, while control charts track performance over time.
System suitability testing is performed before and during analytical runs to confirm that the instrument and method are working as expected. Typical checks include retention time, peak area precision, resolution between critical pairs, tailing factor, and theoretical plate count. Acceptance criteria are set in the method or pharmacopeial monograph. If a suitability check fails, the run may be rejected and the instrument or sample preparation may need investigation. This practice helps prevent release of data from a system that has drifted out of control.
Quality control samples are inserted at intervals to monitor accuracy and precision throughout a batch. Blank samples detect contamination, while spiked samples assess recovery from the sample matrix. Calibration standards establish the relationship between detector response and concentration, and control samples are prepared independently from them whenever possible. Laboratories also participate in proficiency testing and maintain audit trails, instrument logs, and reagent records. Ongoing review of control charts can reveal trends before they cause out-of-specification results.
Method validation demonstrates that an HPLC procedure is suitable for its intended purpose. Common validation parameters include accuracy, precision, specificity, linearity, range, limit of detection, limit of quantification, and robustness. Accuracy reflects agreement with a reference value, while precision describes repeatability under defined conditions. Specificity shows whether the method can measure the analyte in the presence of impurities or matrix components. Validation documents are reviewed before a method is used for routine testing or regulatory submissions.
The binding of S-arrestin to rhodopsin is specific and involves changes that occur in rhodopsin after activation. Important serine (Ser) and threonine (Thr) residues in rhodopsin's tail, particularly Thr-340 and Ser-343, are phosphorylated by enzymes called GRKs. These phosphorylated residues strongly attract S-arrestin, helping it bind tightly and effectively shut down rhodopsin's signaling. Additionally, studies of the protein structure have shown that during activation, rhodopsin's transmembrane helix 7 (TM7) and helix 8 change shape. These changes expose a binding site that interacts with a specific part of arrestin called the "finger loop." This interaction, clearly seen in the crystal structure (PDB ID: 4ZWJ), shows how arrestin fits precisely onto activated and phosphorylated rhodopsin, efficiently stopping the visual signal. Arrestin at the U.S. National Library of Medicine Medical Subject Headings (MeSH)
The methyl ricinoleate is converted to heptanal and methyl undecenoate by combining with steam in a cracking furnace at 400 - 575 °C. The cleavage of the aliphatic chain occurs selectively between the hydroxymethylene and the allyl-methylene group. Besides heptanal and methyl undecenoate, a mixture of methyl esters of saturated and unsaturated C18-carboxylic acids is obtained. This mixture is known under the trade name Esterol and is used as a lubricant additive. The methyl ester is next hydrolyzed to give 10-undecenoic acid (undecylenic acid). The undecenoic acid is dissolved in toluene and, in the presence of the radical initiator benzoyl peroxide (BPO), gaseous hydrogen bromide is added, in contrary to the Markovnikov rule ("anti-Markovnikov"). When cooled to 0 °C, the fast and highly exothermic reaction produces 11-bromoundecanoic acid in 95% yield - the Markovnikov product 10-bromoundecanoic acid is produced in small quantities as a by-product. Toluene and unreacted hydrogen bromide are extracted under reduced pressure and reused.
In pharmacology, relative bioavailability measures the bioavailability (estimated as the AUC) of a formulation (A) of a certain drug when compared with another formulation (B) of the same drug, usually an established standard, or through administration via a different route. When the standard consists of intravenously administered drug, this is known as absolute bioavailability (see above). F r e l = 100 ⋅ A U C A ⋅ D B A U C B ⋅ D A {\displaystyle F_{\mathrm {rel} }=100\cdot {\frac {AUC_{\mathrm {A} }\cdot D_{\mathrm {B} }}{AUC_{\mathrm {B} }\cdot D_{\mathrm {A} }}}}
The AAA proteins contain two domains, an N-terminal alpha/beta domain that binds and hydrolyzes nucleotides (a Rossmann fold) and a C-terminal alpha-helical domain. The N-terminal domain is 200-250 amino acids long and contains Walker A and Walker B motifs, and is shared in common with other P-loop NTPases, the superfamily which includes the AAA family. Most AAA proteins have additional domains that are used for oligomerization, substrate binding and/or regulation. These domains can lie N- or C-terminal to the AAA module. Some classes of AAA proteins have an N-terminal non-ATPase domain which is followed by either one or two AAA domains (D1 and D2). In some proteins with two AAA domains, both are evolutionarily well conserved (like in Cdc48/p97). In others, either the D2 domain (like in Pex1p and Pex6p) or the D1 domain (in Sec18p/NSF) is better conserved in evolution. While the classical AAA family was based on motifs, the family has been expanded using structural information and is now termed the AAA family.
Sources: en.wikipedia.org
It was hoped that ANGPTL8 or its homolog in humans may provide an effective treatment for type 2 diabetes and perhaps even type I diabetes. Unfortunately, since new data have greatly called into question the ability of ANGPTL8 to increase beta-cell replication, its potential use as a therapy for type 2 diabetes is limited. Inhibition of ANGPTL8 represents a possible therapeutic strategy for hypertriglyceridemia. In a clinical trial, a human ANGPTL3/8 monoclonal antibody reduced the concentration of triglycerides (-70%), and low-density lipoprotein cholesterol (-32%), while increasing HDL- cholesterol (+27%), representing a promising therapy for multiple lipid disorders. Human C19orf80 genome location and C19orf80 gene details page in the UCSC Genome Browser.
Alfred Ellis Wilhelmi (1910–1994) was an American endocrinologist recognized for contributing to the understanding of anterior pituitary hormones. Born in Lakewood, Ohio, Wilhelmi attended Cleveland public schools. Wilhelmi earned a B.S. degree in premedical sciences from Western Reserve University in 1933. He then attended Oxford University as a Rhodes Scholar, where he obtained a B.A. in 1933 and Ph.D. in animal physiology in 1937. He then joined Yale University's Biochemistry Department, rising to the position of Professor in 1950. Wilhelmi chaired the Department of Biochemistry at Emory University School of Medicine from 1950 to 1977. In 1960, he was named Charles Howard Candler Professor of Biochemistry. In 1979, he received Emory's Thomas Jefferson award for service to the university and community. Wilhelmi also was President of the Endocrine Society from 1968 to 1969. During his career, he published over 80 articles in scientific journals.
GPCRs become desensitized when exposed to their ligand for a long period of time. There are two recognized forms of desensitization: 1) homologous desensitization, in which the activated GPCR is downregulated; and 2) heterologous desensitization, wherein the activated GPCR causes downregulation of a different GPCR. The key reaction of this downregulation is the phosphorylation of the intracellular (or cytoplasmic) receptor domain by protein kinases. Cyclic AMP-dependent protein kinases (protein kinase A) are activated by the signal chain coming from the G protein (that was activated by the receptor) via adenylate cyclase and cyclic AMP (cAMP). In a feedback mechanism, these activated kinases phosphorylate the receptor. The longer the receptor remains active the more kinases are activated and the more receptors are phosphorylated. In β2-adrenoceptors, this phosphorylation results in the switching of the coupling from the Gs class of G-protein to the Gi class. cAMP-dependent PKA mediated phosphorylation can cause heterologous desensitisation in receptors other than those activated.
Afamelanotide, sold under the brand name Scenesse, is a medication used to prevent phototoxicity and to reduce pain from light exposure for people with erythropoietic protoporphyria, a rare form of genetic sun sensitivity. Afamelanotide is a melanocortin 1 receptor (MC1 receptor) agonist and a synthetic peptide and analogue of α-melanocyte stimulating hormone. It is administered as subcutaneous implant. In the European Union, afamelanotide is indicated for the prevention of phototoxicity in adults with erythropoietic protoporphyria. In the United States, afamelanotide is indicated for increasing pain-free light exposure in adults with a history of reactions to light (phototoxicity) from erythropoietic protoporphyria.
Antimicrobial peptides are produced by species across the tree of life, including: bacteria (e.g. bacteriocin, and many others) fungi (e.g. peptaibols, plectasin, and many others) cnidaria (e.g. hydramacin, aurelin) many from insects and arthropods (e.g. cecropin, attacin, melittin, mastoparan, drosomycin, thioester-containing protein 1) amphibia, frogs (magainin, dermaseptin, aurein, and others) birds (e.g. avian defensins) and mammals (e.g. cathelicidins, alpha- and beta-defensins, regIII peptides) Research has increased in recent years to develop artificially-engineered mimics of antimicrobial peptides such as SNAPPs, in part due to the prohibitive cost of producing naturally-derived AMPs. An example of this is the facially cationic peptide C18G, which was designed from the C-terminal domain of human platelet factor IV. Currently, the most widely used antimicrobial peptide is nisin; being the only FDA approved antimicrobial peptide, it is commonly used as an artificial preservative.
Sources: en.wikipedia.org
Marcey Lynn Waters is the Glen H. Elder Jr., Distinguished Professor of Chemistry at the University of North Carolina, Chapel Hill (UNC-CH). She is an organic chemist whose research is at the interface of chemical biology and supramolecular chemistry. Waters has received multiple awards for research, teaching, and advocating for women in science. She served as president of the American Peptide Society (APS) from 2017 to 2019. Waters graduated from the University of California, San Diego with a degree in chemistry in 1992. While an undergraduate, she worked with Prof. Charles L. Perrin studying fundamental aspects of aromaticity. Waters entered the University of Chicago for her doctoral degree in chemistry, working with Prof. William D. Wulff studying the mechanism for the Wulff-Dotz benzannulation reaction between Fischer carbene complexes. and alkynes. Walters graduated from Chicago in 1997 with a PhD in chemistry. She was an NIH postdoctoral fellow in Prof. Ronald Breslow's group from 1997 to 1999, where she worked on dinuclear metalloenzyme mimics and antiaromaticity.
The second modification allows a substantial simplification of the classic theory, and so application in complex metabolic networks. The theory on synthesizing units is used in dynamic energy budget theory, where 4 basic modes are distinguished: the substrates can be substitutable or supplementary (= complementary); if the transformations A -> C and B -> C can occur, substrates A and B are said to be substitutable with respect to their transformation to C, if both are required to produce C they are said to be supplementary the processing of these substrates by SUs can be sequential or parallel; if in the transformation A + B -> C the binding of substrate A to the SU does not affect that of B, these substrates are processed simultaneously, if not these substrates are processed sequentially Mixtures of the 4 basic modes can occur, especially if the substrates represent generalized compounds, rather than pure chemical compounds. A generalized compound is a mixture of chemical compounds that does not change in composition.
TP0586532 is an experimental antibiotic drug, which acts as a potent and selective inhibitor of the bacterial enzyme UDP-3-O-acyl-N-acetylglucosamine deacetylase (LpxC). This enzyme is important for the production of Lipid A, a key component of the cell membrane of Gram-negative bacteria. Previous inhibitors of LpxC have failed to progress into clinical trials in humans, mostly because of off-target cardiovascular toxicity, so TP0586532 was based on a different structural class which is hoped to reduce this risk. In animal studies it shows activity against carbapenem-resistant Klebsiella pneumoniae but has not yet progressed into human trials. LPC-233
The glycoconjugate is the product formed by oligosaccharides covalently bonding to other biomolecules such as proteins and lipids. They play indispensable roles in the biological activities of mammalian cells from energy generation to cell signalling. These glycoconjugates with short oligosaccharide structures are important for the characterization and purification in the course glycoconjucate vaccine developments. Therefore, research in the engineering of the glycosyl precursors that create oligosaccharides with controlled size is important in carbohydrate synthesis.
Sources: en.wikipedia.org
Method validation is the documented process of confirming that an HPLC procedure is suitable for its intended use. It evaluates accuracy, precision, specificity, linearity, range, detection limits, and robustness. Validation criteria depend on the regulatory context and the sample type.
System suitability tests are short checks performed before or during an HPLC run to verify instrument and method performance. They often include resolution, tailing factor, theoretical plates, and injection precision. Results must meet predefined limits for sample data to be accepted.
HPLC retention time alone cannot definitively identify an unknown substance. A match with a reference standard under identical conditions provides supporting evidence. Confirmation typically requires mass spectrometry, nuclear magnetic resonance, or another orthogonal technique.
System suitability is a set of checks performed before and during a run to confirm that the instrument, column, and method work as expected. Common checks include resolution, tailing factor, theoretical plates, and relative standard deviation of replicate injections. Failure triggers troubleshooting or method adjustment.